NMD SCHEDULE OF FEES AND CHARGES
Electricity Standards Section
|
Type of Equipment / Device |
Range or Capacity |
Calibration Fee (PHP) |
|
Conductivity Meter |
0.1 µS (minimum) |
845.00 |
|
Centrifuge |
Up to 18,000 r/min |
800.00 |
|
DC Voltage Standard (per voltage level) |
1.018 V and 10 V |
5,590.00 |
|
Decade Resistance Box (per dial) |
0 Ω to 100 MΩ |
1,140.00 |
|
Double Bridge |
Up to 100 MΩ |
2,500.00 |
|
Earth Tester |
Up to 100 MΩ |
1,350.00 |
|
per succeeding range |
400.00 |
|
|
Frequency Calibrator |
Up to 225 MHz |
2,700.00 |
|
Frequency Counter |
10 MHz |
1,550.00 |
|
GPS Receiver |
1 pps |
9,000.00 |
|
Ground Strap Tester / Checker |
Up to 100 MΩ |
800.00 |
|
Illuminance / Lux / Light Meter |
(380 to 2000) lux |
2,600.00 |
|
Insulation Tester |
Up to 1000 V |
1,050.00 |
|
per succeeding range |
350.00 |
|
|
Kelvin Bridge |
Up to 100 MΩ |
2,500.00 |
|
mA Calibrator |
Up to 1000 mA |
1,890.00 |
|
Megohmmeter / Megger Tester |
Up to 1000 V |
1,090.00 |
|
per succeeding range |
350.00 |
|
|
Multimeter, Digital |
4 ½ digits; Up to 1000 Vdc; Up to 650 Vac; Up to 1 A AC/DC; Up to 100 MΩ |
2,500.00 |
|
6 ½ digits; Up to 1000 Vdc; Up to 650 Vac; Up to 1 A AC/DC; Up to 100 MΩ |
17,000.00 |
|
|
pH Meter |
0 to 14 pH |
845.00 |
|
pH Simulator |
0 to 14 pH |
845.00 |
|
Process Calibrator (input/output) |
Up to 1000 Vdc; Up to 650 Vac; Up to 1 A AC/DC; Up to 100 MΩ |
4,900.00 |
|
Puncture Tester |
Up to 5 kV AC/DC; Up to 1 A AC/DC; Up to 100 MΩ |
1,700.00 |
|
Resistance Bridge / Wheatstone Bridge |
1 Ω to 10 MΩ |
1,700.00 |
|
Stopwatch / Timer |
15 Minutes (minimum) |
800.00 |
|
Standard Resistor (by Ratio) |
1 Ω to 1 MΩ |
6,500.00 |
|
Stroboscope |
Up to 99,000 r/min |
800.00 |
|
Tachometer (non-contact type) |
Up to 18,000 r/min |
800.00 |
|
Time Mark Generator |
Up to 225 MHz |
2,450.00 |
Pressure and Force Standards Section
|
Type of Equipment / Device |
Range or Capacity |
Calibration Fee (PHP) |
|
Absolute Pressure Calibrator |
0.1 MPa to 100 MPa |
6,110.00 |
|
Absolute Pressure Industrial Gauge |
0.1 MPa to 100 MPa |
975.00 |
|
Absolute Pressure Test Gauge |
0.1 MPa to 100 MPa |
3,055.00 |
|
Hydraulic Pressure Balance / Deadweight Tester |
0.1 MPa to 100 MPa |
20,150.00 |
|
Hydraulic Pressure Calibrator |
0.1 MPa to 100 MPa |
6,110.00 |
|
Hydraulic Pressure Gauge |
0.1 MPa to 100 MPa |
975.00 |
|
Hydraulic Pressure Test Gauge |
0.1 MPa to 100 MPa |
3,055.00 |
|
Pneumatic Pressure Balance |
0 bar to 40 bar |
20,150.00 |
|
Deadweight Pressure Tester |
0 bar to 40 bar |
20,150.00 |
|
Pneumatic Pressure Calibrator |
0 bar to 200 bar |
6,110.00 |
|
Pneumatic Pressure Gauge |
0 bar to 20 bar |
975.00 |
|
Pneumatic Pressure Test Gauge |
0 bar to 20 bar |
3,055.00 |
|
Testing of Sphygmomanometer |
0 mmHg to 250 mmHg |
1,300.00 |
|
Vacuum Calibrator |
0 bar to -1 bar |
6,200.00 |
|
Vacuum Gauge |
0 bar to -1 bar |
975.00 |
|
Vacuum Test Gauge |
0 bar to -1 bar |
3,055.00 |
Force
| Type of Equipment / Device | Method/Accuracy | Range or Capacity | Calibration Fee (PHP) | Remarks |
| Durometer A | Comparative Measurement | 0 HA to 90 HA | 780 | |
| Durometer D | 0 HD to 90 HD | 1,560.00 | ||
| Load Cell/Proving Ring | According to ISO 376 | less than 5kN | 5800 | Per Direction |
| 5kN to 10kN | 8,200 | |||
| 10kN to 100kN | 10,200 | |||
| 100kN to 1000kN | 13,600 | |||
| Force Testing Machines | According to ISO 7500 (5 test pts. Per range)* |
2kN to 100kN | 3,700 | Compression mode |
| 100kN to 2000kN | 4200 | |||
| 2kN to 20kN | 3700 | Tension Mode | ||
| 20kN to 100kN | 4200 | |||
| 100 kN to 1000 kN | 4800 | |||
| *per additional test point | 750 | |||
| Push-Pull Gauges/ Dynamometer/ Crane Scale/ Low Accuracy Force Transducers |
Comparative Measurement | Less than 0.2 kN | 1300 | Used as reference for other low accuracy measurements |
| 0.2 kN to 2 kN | 2400 | |||
| 2 kN to 100 kN | 3100 | |||
| 100 kN to 1000 kN | 3900 | |||
| According to ISO 376:2011 | Less than 2 kN | 3100 | Used for verification of testing machines | |
| 2 kN to 10 kN | 4200 | |||
| 10 kN to 100 kN | 6400 | |||
| 100 kN to 1000 kN | 7800 | |||
| Platform Weighing Scales (Axle Weigher) | Comparative Measurement using standard load cell | up to 500 kN | 3600 | Per Device |
| Torque Wrench | Comparative Measurement using standard torque transducer | less than 50 N-m | 2100 | Both Direction (CW & CCW) |
| less than 100 N-m | 3500 | |||
| less than 500 N-m | 5000 | |||
| greater than 500 N-m | 6300 |
Length Standards Section
|
Type of Equipment / Device |
Range or Capacity |
Calibration Fee per Piece (PHP) |
|
Gauge Block Grade 0 (Steel) |
0.5 mm to 100 mm |
1,160.00 |
|
Gauge Block Grade 1 (Steel) |
1,030.00 |
|
|
Gauge Block Grade 2 (Steel) |
1,030.00 |
Thermometry and Hygrometry Standards Section
Contact Thermometry
|
Type of Equipment / Device |
Range or Capacity |
Calibration Fee (PHP) |
|
Digital Thermometer |
-30 °C to +250 °C (first 4 cal. points) |
2,180.00 |
|
per additional cal. point |
650.00 |
|
|
per additional probe |
1,090.00 |
|
|
Industrial Platinum Resistance Thermometer |
-30 °C to +250 °C (first 6 cal. points) |
11,700.00 |
|
per additional cal. point |
975.00 |
|
|
Liquid-in-Glass Thermometer |
-30 °C to +250 °C (first 4 cal. points) |
2,180.00 |
|
per additional cal. point |
650.00 |
|
|
(Wall / Refrigerator / Bimetallic) Thermometer |
-30 °C to +250 °C (first 4 cal. points) |
1,820.00 |
|
per additional cal. point |
650.00 |
|
|
Thermocouple with Indicator |
300 °C to 1000 °C (per cal. point) |
2,150.00 |
Non-Contact Thermometry
|
Type of Equipment / Device |
Range or Capacity |
Calibration Fee (PHP) |
|
Infrared Thermometer |
Low-range: (0, 35, 50, 100, 120) °C |
2,800.00 |
|
High-range: (0, 100, 200, 350, 500) °C |
2,800.00 |
Enclosures
|
Type of Equipment / Device |
Range or Capacity |
Calibration Fee (PHP) |
|
Furnace |
300 °C to 1000 °C (first cal. point) |
2,730.00 |
|
per additional cal. point |
1,400.00 |
|
|
Oven / Freezer / Incubator / Cold Storage / Walk-in Enclosures / Water Bath / Refrigerator, etc. |
-30 °C to +250 °C (first cal. point) |
2,730.00 |
|
per additional cal. point |
1,400.00 |
Hygrometry
|
Type of Equipment / Device |
Range or Capacity |
Calibration Fee (PHP) |
|
Thermo-hygrometer |
(20, 25, 30) °C; (40, 60 and 80) %rh at 23 °C |
1,274.00 |
|
Thermo-hygrograph |
(20, 25, 30) °C; (40, 60 and 80) %rh at 23 °C |
3,822.00 |
Moisture
|
Type of Equipment / Device |
Range or Capacity |
Calibration Fee (PHP) |
Remarks |
|
Wood Moisture Meter |
9 % to 21 % |
840.00 |
Test |
|
Rice / Grain Moisture Meter |
9 % to 21 % |
2,500.00 |
Calibration; 5 samples of varying moisture content |
|
Rice / Grain Moisture Meter |
9 % to 21 % |
1,800.00 |
Test; 1 sample |
Volume and Flow Standards Section
|
Type of Equipment / Device |
Range or Capacity |
Calibration Fee (PHP) |
|
Burette |
0.1 mL to 100 mL (5 cal. points) |
689.00 |
|
Volumetric Flask |
1 mL to 5000 mL |
689.00 |
|
Multiple Delivery Dispenser |
1 µL to 100000 µL (5 cal. points) |
1,900.00 |
|
Piston Pipette |
1 µL to 10000 µL (3 cal. points) |
1,900.00 |
|
per addition cal. point |
630.00 |
|
|
Pipette |
0.1 mL to 100 mL |
689.00 |
|
Proving Tanks (Gravimetric) |
up to 500 L |
5,200.00 |
|
Proving Tanks (Volumetric) |
100L to 400L |
3,500.00 |
|
Proving Tanks (Volumetric) |
>400L to 2000 L |
3,500.00 |
|
Proving Tanks (Volumetric) |
>2000 L to 5000 L |
4,500.00 |
|
Road Tankers (Volume capacity determination)
|
up to 10000 L |
920.00 |
|
>10000 L to 15000 L |
1,370.00 |
|
|
>15000 L to 20000 L |
1,840.00 |
|
|
>20000 L to 25000 L |
2,300.00 |
|
|
>25000 L to 30000 L |
2,750.00 |
|
|
>30000 L to 35000 L |
3,200.00 |
|
|
>35000 L to 40000 L |
3,650.00 |
|
|
>40000 L to 45000 L |
4,100.00 |
|
|
>45000 L to 50000 L |
4,200.00 |
|
|
Test Measure (Gravimetric) |
5 L , 10 L , 20 L |
2,340.00 |
|
Test Measure (Volumetric) |
5 L , 10 L |
390.00 |
|
Test Measure (Volumetric) |
20 L |
780.00 |
Density
|
Type of Equipment / Device |
Range or Capacity |
Calibration Fee (PHP) |
|
Hydrometers |
(600 to 2000) kg/m³ |
1,200.00 |
Mass Standards Section
Calibration of Weights
|
Class / Type |
Range |
Calibration Fee per Piece (PHP) |
Remarks |
|
OIML Class E2 |
1 mg to 50 g |
1,090.00 |
DAkkS Certificate (1 mg to 1 kg only)
NML Certificate (2 kg to 50 kg) |
|
100 g to 500 g |
1,480.00 |
||
|
1 kg to 10 kg |
1,660.00 |
||
|
20 kg to 50 kg |
1,990.00 |
||
|
OIML Class F1 / F2 |
1 mg to 50 g |
600.00 |
DAkkS Certificate (1 mg to 50 kg only)
NML Certificate (100 kg to 200 kg) |
|
100 g to 500 g |
650.00 |
||
|
1 kg to 10 kg |
950.00 |
||
|
20 kg to 50 kg |
1,050.00 |
||
|
100 kg to 200 kg |
2,100.00 |
||
|
OIML Class M1 / M2 / M3 |
1 mg to 500 g |
450.00 |
DAkkS Certificate (1 mg to 50 kg only)
NML Certificate (100 kg to 200 kg) |
|
1 kg to 10 kg |
600.00 |
||
|
20 kg to 50 kg |
700.00 |
||
|
100 kg to 200 kg |
1,500.00 |
||
|
500 kg |
2,100.00 |
||
|
Free Nominal (Stainless Steel) |
1 mg to 50 g |
600.00 |
DAkkS Certificate (1 mg to 50 kg only)
NML Certificate (100 kg to 200 kg) |
|
> 50 g to 500 g |
650.00 |
||
|
> 500 g to 10 kg |
950.00 |
||
|
> 10 kg to 50 kg |
1,050.00 |
||
|
> 50 kg to 200 kg |
2,100.00 |
||
|
Free Nominal (Other Materials) |
1 mg to 500 g |
450.00 |
DAkkS Certificate (1 mg to 50 kg only)
NML Certificate (100 kg to 500 kg) |
|
> 500 g to 10 kg |
600.00 |
||
|
> 10 kg to 50 kg |
700.00 |
||
|
> 50 kg to 200 kg |
1,500.00 |
||
|
> 200 kg to 500 kg |
2,100.00 |
Calibration / Testing of Nonautomatic Weighing Instruments (NAWI)
|
Type of Service |
Range / Accuracy Class |
Calibration Fee per Piece (PHP) |
Remarks |
|
Calibration of NAWI, electronic type only (on-site calibration) |
Up to 2 kg (using OIML Class E2) |
2,000.00 |
DAkkS Certificate (up to 600 g only) |
|
NMD Certificate (>600 g up to 2 kg) |
|||
|
Up to 60 kg (using OIML Class F1) |
1,530.00 |
DAkkS Certificate (up to 20 kg only) |
|
|
NMD Certificate (>20 kg up to 60 kg) |
|||
|
Up to 200 kg (using OIML Class F2) |
1,530.00 |
DAkkS Certificate (up to 60 kg only) |
|
|
NMD Certificate (>60 kg up to 200 kg) |
|||
|
Up to 300 kg (using OIML Class M1) |
1,530.00 |
NMD Certificate |
|
|
Testing of NAWI, electronic and mechanical types |
High Accuracy* (using OIML Class F2; 1 tonne) |
1,200.00 |
NMD Certificate |
|
Medium Accuracy* & Ordinary Accuracy* (using OIML Class M1 and substitution material; 1 tonne) |
1,080.00 |
||
|
*per additional tonne |
20.00 |
On-Site Calibration Service
|
Additional Daily Surcharge Fee per NMD personnel |
PHP 1,500.00 |
